Don't panic! For Peel & Stick, push small bubbles to the edge with your squeegee. For stubborn ones, use a fine sewing needle to poke a tiny hole in the center, then press the air out. It will disappear instantly.
Let’s Get This on the Wall!
Easy Install Guide
You don't need to be a pro to create a magical space. Grab a friend, put on some music, and follow these simple steps.
Before you start
Gather Your Tools
Success starts with the right setup. Here is everything you need before you unroll the first panel.
Smoothing Tool
We included a premium felt-edged squeegee in your box!
Level & Pencil
To mark a straight line for your first panel.
Sharp Knife
A craft knife (like X-Acto) with fresh blades for trimming.
Step Stool
To help you reach the top corners comfortably.
Wait! Is your wall ready?
How to Prep Your Wall
The secret to wallpaper that sticks perfectly is a clean, dry wall. Even if it looks clean, give it a quick wipe down with warm water and a microfiber cloth (no chemicals). Let it dry completely for 24 hours before you start.
🚨 The "Fresh Paint" Warning:
Did you just paint the room? You must wait 30 days for the paint to fully cure ("gas out") before applying wallpaper. If you stick it too soon, the bubbles from the paint will push the wallpaper off the wall!
Step-by-Step
How to Install Your Wallpaper
Choose your material type below to see the specific instructions.
Peel & Stick
Prepasted
Step 1: The Plumb Line (Don't skip this!)
Walls are rarely straight. Measure the width of your panel minus 1 inch from the corner. Use a level to draw a straight vertical line. This is your guide!
Step 2: Peel & Stick the Top
Peel back the top 10 inches of backing. Stick it to the top of the wall, aligning the edge perfectly with your pencil line.
Step 3: The "Scroll" Method
Slowly pull the backing down while smoothing the paper against the wall with your included squeegee. Work from the center outwards to push out air.
Step 4: The Butt Joint (No Overlap)
For the next panel, line up the pattern at eye level. Push the edges together until they "kiss". Do not overlap the panels.
Step 5: Trim & Finish
Use your squeegee to press the paper into the baseboard, then use your sharp knife to trim the excess.
Step 1: Prep & Organize
Cut your panels apart. Mark a vertical "Plumb Line" on your wall using a level (see Step 1 in the Peel & Stick guide above).
Step 2: Activate the Glue
Lay the panel face down and spray the back evenly with water (or submerge in a water tray for 15 seconds).
Step 3: "Book" the Paper
Gently fold the pasted sides onto themselves (glue to glue) without creasing. Let it sit for 3-5 minutes to activate the adhesive.
Step 4: Slide & Match
Unfold the top half and stick it to the wall, aligning with your pencil line. Smooth it out with a damp sponge. Repeat for the bottom half.
Step 5: Wipe & Trim
Gently wipe off any excess glue on the front with a damp sponge. Trim the excess at the ceiling and floor with a sharp knife.
Common Questions & Quick Fixes
Ran into a snag? Don't panic! Most installation "hiccups" (like air bubbles or wrinkles) are completely normal and easy to fix.
Help! I see air bubbles.
How do I cut around outlets and switches?
Can I install this on textured walls?
The pattern lines up at eye level but not at the bottom. Any ideas?
Is it safe for bathrooms?
Do I really have to wait 30 days after painting?
Will this damage my wall when I move?
How do I clean the wallpaper?
Installation Support
We're Here to Help
Whether you have a quick question before you start or need advice while you work, our team is ready to guide you.
